Difference between revisions of "Guides:MESS - Installing MS-DOS 6.22"

From Wah!ki
Jump to navigation Jump to search
Line 79: Line 79:
 
== Troubleshooting ==
 
== Troubleshooting ==
 
=== Installation ===
 
=== Installation ===
If your machine appears to hang here reboot the machine again and press '''F5''' to drop to a '''A:\>''' prompt.
+
If your machine appears to hang at the '"Starting MS-DOS"'' prompt.  
  
 +
Reboot the machine again and press '''F5''' when you see the '"Starting MS-DOS"'' prompt to drop to a '''A:\>''' prompt.
 +
 +
When you reach the A:\> prompt type DIR to list the directory contents and look for SETUP.EXE
 +
 +
Run SETUP.EXE to begin the installation
 +
'''
 +
<nowiki>
 +
A:\>SETUP.EXE/nowiki>
 +
'''
 +
 +
Follow the prompts as mentioned above.
  
  

Revision as of 05:58, 10 February 2020

Installing DOS 6.22 in MESS

Introduction

This guide will walk you through the process of getting MS-DOS running within the MAME ct486 machine. We'll cover off some of the specific tweaks required when installing DOS

For general information on the MESS project and how to use it including external references see the dedicated MESS Page

Prerequisites

  • A CHD
  • A copy of the MS-DOS 6.22 floppies.

Process

Having created a CHD to use you will now boot the ct486 driver with the hdd attached.


The ct486 driver doesn't have an auto configure HDD in the bios so you'll need to know your Cylinders, Heads and Sectors (CHS) values in relation to the CHD you are going to use. If you don't have the CHS information you can query the CHD image directly for this information, refer to the chdman Guide on how to do this.


Boot the ct486 machine with the hdd attached

$ ./mame64 ct486 -hard1 <chdname.chd>

On first boot you can expect the CMOS checksum to fail, the machine BIOS setup values will need to be entered.


Hit the F1 key on your keyboard to resume and enter the BIOS setup screen.


Under STANDARD CMOS SETUP configure the HDD and the FDD if not already configured


HDD (This is where you will need your CHS values from earlier)

Type: 47=USER TYPE
Cyln: <Cylinders>
Head: <Heads>
Sect: <Sectors>

It is not necessary to modify WPcom or LZone


FDD

Type: 1.44MB

Press ESC to exit this screen and select WRITE TO CMOS AND EXIT from the main menu, answer Y when prompted


This only needs to be completed the first time you boot the machine. MAME will create a nvram file on the hosts hard drive (not the CHD) under nvram/ct486 which will maintain the configured state between machine boots.


Shutdown the machine (close MAME) and restart the ct486 with the first floppy disk installed

$ ./mame64 ct486 -hard1 <chdname.chd> -flop1 <disk01.img>

The machine should begin to boot the MS-DOS setup you will known this because you will see "Starting MS-DOS" on the machine. If your machine appears to hang here see Troubleshooting -> Installation further down this page.


Continue through the standard setup as prompted, applying the defaults unless you have specific requirement for partitioning etc.


When prompted for the next disk press the Scroll Lock key to toggle to Partial Emulation mode and press TAB to enter the MAME UI. Scroll down to File Manager then select the floppy drive disk image, press Enter to browse for the next disk. Once the disk has been selected press TAB again close the MAME UI


If required interact with the machine as prompted so it checks for the newly inserted disk, e.g. press Enter


Once the setup complets the machine will prompt you and then reboot, power off the machine (close MAME) and start the machine without the disk image attached so it will boot from the drive


Troubleshooting

Installation

If your machine appears to hang at the '"Starting MS-DOS" prompt.

Reboot the machine again and press F5 when you see the '"Starting MS-DOS" prompt to drop to a A:\> prompt.

When you reach the A:\> prompt type DIR to list the directory contents and look for SETUP.EXE

Run SETUP.EXE to begin the installation

A:\>SETUP.EXE/nowiki>
'''

Follow the prompts as mentioned above.



For reference the md5 of the disks we use in this guide are
'''
 <nowiki>
sha1sums